Integrated Circuits

Product Details:

^{The 80C196KC 16-bit microcontroller is a high performance member of the MCS 96 microcontroller family.}

Additional Information:

• Delivery Time: 3 DAYS

Product Details:

The MAX481, MAX483, MAX485, MAX487–MAX491, and MAX1487 are low-power transceivers for RS-485 and RS422 communication. Each part contains one driver and one receiver. The MAX483, MAX487, MAX488, and MAX489 feature reduced slew-rate drivers that minimize EMI and reduce reflections caused by improperly terminated cables, thus allowing error-free data transmission up to 250kbps. The driver slew rates of the MAX481, MAX485, MAX490, MAX491, and MAX1487 are not limited, allowing them to transmit up to 2.5Mbps. These transceivers draw between 120µA and 500µA of supply current when unloaded or fully loaded with disabled drivers. Additionally, the MAX481, MAX483, and MAX487 have a low-current shutdown mode in which they consume only 0.1µA. All parts operate from a single 5V supply. Drivers are short-circuit current limited and are protected against excessive power dissipation by thermal shutdown circuitry that places the driver outputs into a high-impedance state. The receiver input has a fail-safe feature that guarantees a logic-high output if the input is open circuit. The MAX487 and MAX1487 feature quarter-unit-load receiver input impedance, allowing up to 128 MAX487/ MAX1487 transceivers on the bus. Full-duplex communications are obtained using the MAX488–MAX491, while the MAX481, MAX483, MAX485, MAX487, and MAX1487 are designed for half-duplex applications.

Additional Information:

• Delivery Time: 3 days

Product Details:

Based on a microcoded execution unit and an advanced CMOS manufacturing technology, the Z80180, Z8S180, Z8L180 (Z8X180) is an 8-bit MPU which provides the benefits of reduced system costs and low power operation while offering higher performance and maintaining compatibility with a large base of industry standard software written around the ZiLOG Z8X CPU.

Additional Information:

• Delivery Time: 3 days

Product Details:

The DG200B is a dual, single-pole, single-throw analog switch designed to provide general purpose switching of analog signals. This device is ideally suited for designs requiring a wide analog voltage range coupled with low on-resistance. The DG200B is designed on Vishay Siliconix’ improved PLUS-40 CMOS process. An epitaxial layer prevents latchup. Each switch conducts equally well in both directions when on, and blocks up to 30 V peak-to-peak when off. In the on condition, this bi-directional switch introduces no offset voltage of its own.

Additional Information:

• Delivery Time: 3 DAYS

Product Details:

Product Details:

Product Details:

Product Details:

Product Details:

Product Details:

Product Details:

Product Details:

Product Details:

We are offering  ICL7621DCPAZ Intersil Integrated Circuits to our valuable customers.

Product Details:

The LM1086 is a series of low dropout positive voltage regulators with a maximum dropout of 1.5V at 1.5A of load current. It has the same pin-out as National Semiconductor’s industry standard LM317. The LM1086 is available in an adjustable version, which can set the output voltage with only two external resistors. It is also available in six fixed voltages: 1.8V, 2.5V, 2.85V, 3.3V, 3.45V and 5.0V. The fixed versions integrate the adjust resistors. The LM1086 circuit includes a zener trimmed bandgap reference, current limiting and thermal shutdown. The LM1086 series is available in TO-220, TO-263, and LLP packages. Refer to the LM1084 for the 5A version, and the LM1085 for the 3A version.

Additional Information:

• Delivery Time: 3 days

Product Details:

The L293B and L293E are quad push-pull drivers capable of delivering output currents to 1A per channel. Each channel is controlled by a TTLcompatible logic input and each pair of drivers (a full bridge) is equipped with an inhibit input which turns off all four transistors. A separate supply input is provided for the logic so that it may be run off a lower voltage to reduce dissipation. Additionally, the L293E has external connection of sensing resistors, for switchmode control. The L293B and L293E are package in 16 and 20- pin plastic DIPs respectively ; both use the four center pins to conduct heat to the printed circuit board.

Additional Information:

• Delivery Time: 3 DAYS

Product Details:

Series SN75471 dual peripheral drivers are functionally interchangeable with series SN75451B and series SN75461 peripheral drivers, but are designed for use in systems that require higher breakdown voltages than either of those series can provide at the expense of slightly slower switching speeds than series 75451B (limits are the same as series SN75461). Typical applications include high-speed logic buffers, power drivers, relay drivers, lamp drivers, MOS drivers, line drivers, and memory drivers. The SN75471, SN75472, and SN75473 are dual peripheral AND, NAND, and OR drivers, respectively, (assuming positive logic), with the output of the logic gates internally connected to the bases of the npn output transistors. Series SN75471 drivers are characterized for operation from 0°C to 70°C.

Additional Information:

• Delivery Time: 3 DAYS

Product Details:

The OPAx277 series precision operational amplifiers replace the industry standard OP-177. They offer improved noise, wider output voltage swing, and are twice as fast with half the quiescent current. Features include ultralow offset voltage & driff, low bias current, high common mode rejection, and high power supply rejection. Single, dual, & quad versions have identical specifications, for maximum design flexibility.

Additional Information:

• Delivery Time: 3 DAYS

Product Details:

The MC33035 is a high performance second generation monolithic brushless DC motor controller containing all of the active functions required to implement a full featured open loop, three or four phase motor control system. This device consists of a rotor position decoder for proper commutation sequencing, temperature compensated reference capable of supplying sensor power, frequency programmable sawtooth oscillator, three open collector top drivers, and three high current totem pole bottom drivers ideally suited for driving power MOSFETs. Also included are protective features consisting of undervoltage lockout, cycle−by−cycle current limiting with a selectable time delayed latched shutdown mode, internal thermal shutdown, and a unique fault output that can be interfaced into microprocessor controlled systems. Typical motor control functions include open loop speed, forward or reverse direction, run enable, and dynamic braking. The MC33035 is designed to operate with electrical sensor phasings of 60°/300° or 120°/240°, and can also efficiently control brush DC motors.

Additional Information:

• Delivery Time: 3 DAYS

Product Details:

The DS32kHz is a temperature-compensated crystal oscillator (TCXO) with an output frequency of 32.768kHz. This device addresses applications requiring better timekeeping accuracy, and can be used to drive the X1 input of most Dallas Semiconductor real-time clocks (RTCs), chipsets, and other ICs containing RTCs. This device is available in commercial (DS32kHz) and industrial (DS32kHz-N) temperature versions.

Additional Information:

• Delivery Time: 3 DAYS

Product Details:

The HCPL-4506 and HCPL-0466 contain a GaAsP LED while the HCPL-J456 and the HCNW4506 con­tain an AlGaAs LED. The LED is optically coupled to an inte­grated high gain photo detector. Minimized propagation delay difference between devices makes these optocouplers excellent solutions for improving inverter efficiency through reduced switching dead time. An on chip 20 k??? output pull-up resistor can be enabled by shorting output pins 6 and 7, thus eliminating the need for an external pull-up resistor in common IPM applications. Specifications and performance plots are given for typical IPM applications.

Additional Information:

• Delivery Time: 3 Days

Product Details:

We are offering Silicon Lab C8051F340GQR Integrated Circuits to our valuable customers.

Product Details:

The XTR105 is a monolithic 4-20mA, 2-wire current transmitter with two precision current sources. It provides complete current excitation for platinum RTD temperature sensors and bridges, instrumentation amplifiers, and current output circuitry on a single integrated circuit.
 
Versatile linearization circuitry provides a 2nd-order correction to the RTD, typically achieving a 40:1 improvement in linearity. 

Instrumentation amplifier gain can be configured for a wide range of temperature or pressure measurements. Total unadjusted error of the complete current transmitter is low enough to permit use without adjustment in many applications. This includes zero output current drift, span drift, and nonlinearity. The XTR105 operates on loop power-supply voltages down to 7.5V. 

The XTR105 is available in DIP-14 and SO-14 surfacemount packages and is specified for the –40°C to +85°C industrial temperature range.

Features:

• Low Unadjusted Error
• Two Precision Current Sources 800µA each
• Linearization
• 2- Or 3 wire RTD Operation
• Low Offset  Drift 0.4µV/°C
• Low Output Current Noise: 30nAPP
• High PSR: 110dB minimum
• High CMR: 86dB minimum
• DIP-14 AND SO-14 Packages

Applications:

• Industrial process control
• Factory Automation
• Scada Remote data Acquisition
• Remote Temperature and pressure transducers

Product Details:

The DG408 is an 8 channel single-ended analog multiplexer designed to connect one of eight inputs to a common output as determined by a 3-bit binary address (A0, A1, A2). The DG409 is a dual 4 channel differential analog multiplexer designed to connect one of four differential inputs to a common dual output as determined by its 2-bit binary address (A0, A1). Break-before-make switching action protects against momentary crosstalk between adjacent channels.

An on channel conducts current equally well in both directions. In the off state each channel blocks voltages up to the power supply rails. An enable (EN) function allows the user to reset the multiplexer/demultiplexer to all switches off for stacking several devices. All control inputs, address (Ax) and enable (EN) are TTL compatible over the full specified operating temperature range. Applications for the DG408, DG409 include high speed data acquisition, audio signal switching and routing, ATE systems, and avionics. High performance and low power dissipation make them ideal for battery operated and remote instrumentation applications. 

Designed in the 44 V silicon-gate CMOS process, the absolute maximum voltage rating is extended to 44 V. Additionally, single supply operation is also allowed. An epitaxial layer prevents latchup.

Features:

• Low on-resistance - R_DS(on): 100 Ω
• Low charge injection - Q: 20 pC
• Fast transition time - tTRANS: 160 ns
• Single supply capability
• 44 V supply max. rating
• TTL compatible logic

Benefits:

• Reduced switching errors
• Reduced glitching
• Improved data throughput
• Reduced power consumption
• Increased ruggedness
• Wide supply ranges

Applications:

• Data acquisition systems
• Audio signal routing
• ATE systems
• Battery powered systems
• Single supply systems
• Medical instrumentation

Product Details:

The AD822 is a dual precision, low power FET input op amp that can operate from a single supply of 5 V to 30 V or from dual supplies of ±2.5 V to ±15 V. It has true single-supply capability with an input voltage range extending below the negative rail, allowing the AD822 to accommodate input signals below ground while in the single-supply mode. Output voltage swing extends to within 10 mV of each rail, providing the maximum output dynamic range. Offset voltage of 800 µV maximum, offset voltage drift of 2 µV/°C, input bias currents below 25 pA, and low input voltage noise provide dc precision with source impedances up to a gigaohm. The 1.8 MHz unity-gain bandwidth, –93 dB total harmonic distortion (THD) at 10 kHz, and 3 V/µs slew rate are provided with a low supply current of 800 µA per amplifier.

Additional Information:

• Delivery Time: 3 DAYS

Product Details:

PC900V0NSZX Series contains an IRED optically coupled to an OPIC chip. It is packaged in a 6 pin DIP, available in SMT gullwing lead-form and Wide SMT gullwing lead-form  option. Input-output isolation voltage(rms) is 5.0kV.

Additional Information:

• Delivery Time: 3 DAYS

Product Details:

The CNY64, CNY65, and CNY66 consist of a phototransistor optically coupled to a gallium arsenide infrared-emitting diode in a 4 pin plastic package. The single components are mounted opposite one another, providing a distance between input and output for highest safety requirements of > 3 mm.

Additional Information:

• Delivery Time: 3 DAYS

Product Details:

The L6208 device is a DMOS fully integrated stepper motor driver with non-dissipative overcurrent protection, realized in BCD technology, which combines isolated DMOS power transistors with CMOS and bipolar circuits on the same chip. The device includes all the circuitry needed to drive a two phase bipolar stepper motor including: a dual DMOS full bridge, the constant off time PWM current controller that performs the chopping regulation and the phase sequence generator, that generates the stepping sequence. Available in PowerDIP24 (20 + 2 + 2), PowerSO36 and SO24 (20 + 2 + 2) packages, the L6208 device features a non-dissipative overcurrent protection on the high-side Power MOSFETs and thermal shutdown.

Additional Information:

• Delivery Time: 3 DAYS

Product Details:

The IL300 linear optocoupler consists of an AlGaAs infrared emitter irradiating an output PIN photodiode and a feedback photodiode. The feedback photodiode captures a percentage of the emitter’s flux and generates a control signal (IP1) that can be used to keep the emitter output constant by adjusting the emitter forward current. This compensates for the emitter’s non-linear, time, and temperature characteristics. The output PIN photodiode produces an output signal (IP2) that is linearly related to the servo optical flux created by the emitter. The time and temperature stability of the input-output coupler gain (K3) is insured by using matched PIN photodiodes that accurately track the output flux of the emitter.

Additional Information:

• Delivery Time: 3 DAYS

Product Details:

The DG406 is a 16 channel single-ended analog multiplexer designed to connect one of sixteen inputs to a common output as determined by a 4-bit binary address. The DG407 selects one of eight differential inputs to a common differential output. Break-before-make switching action protects against momentary shorting of inputs. An on channel conducts current equally well in both directions. In the off state each channel blocks voltages up to the power supply rails. An enable (EN) function allows the user to reset the multiplexer/demultiplexer to all switches off for stacking several devices. All control inputs, address (Ax) and enable (EN) are TTL compatible over the full specified operating temperature range. Applications for the DG406, DG407 include high speed data acquisition, audio signal switching and routing, ATE systems, and avionics. High performance and low power dissipation make them ideal for battery operated and remote instrumentation applications. Designed in the 44 V silicon-gate CMOS process, the absolute maximum voltage rating is extended to 44 V, allowing operation with ± 20 V supplies. Additionally single (12 V) supply operation is allowed. An epitaxial layer prevents latchup. For applications information please request documents 70601 and 70604.

Additional Information:

• Delivery Time: 3 DAYS

Product Details:

The DG300B, DG303B family of monolithic CMOS switches feature three switch configuration options (SPST, SPDT, and DPST) for precision applications in communications, instrumentation and process control, where low leakage switching combined with low power consumption are required. Designed on the Vishay Siliconix PLUS-40 CMOS process, these switches are latch-up proof, and are designed to block up to 30 V peak-to-peak when off. An epitaxial layer prevents latchup. In the on condition the switches conduct equally well in both directions (with no offset voltage) and minimize error conditions with their low on-resistance. Featuring low power consumption (3.5 mW typ.) these switches are ideal for battery powered applications, without sacrificing switching speed. Designed for break-before-make switching action, these devices are CMOS and quasi TTL compatible. Single supply operation is allowed by connecting the V- rail to 0 V.

Additional Information:

• Delivery Time: 3 DAYS

Product Details:

The FT232R is a USB to serial UART interface with the following advanced features:
 Single chip USB to asynchronous serial data transfer interface.  Entire USB protocol handled on the chip. No USB specific firmware programming required.
  Fully integrated 1024 bit EEPROM storing device descriptors and CBUS I/O configuration.
  Fully integrated USB termination resistors.
  Fully integrated clock generation with no external crystal required plus optional clock output selection enabling a glue-less interface to external MCU or FPGA.
 Data transfer rates from 300 baud to 3 Mbaud (RS422, RS485, RS232) at TTL levels.
  128 byte receive buffer and 256 byte transmit buffer utilising buffer smoothing technology to allow for high data throughput.
  FTDI’s royalty-free Virtual Com Port (VCP) and Direct (D2XX) drivers eliminate the requirement for USB driver development in most cases.
  Unique USB FTDIChip-ID™ feature.
  Configurable CBUS I/O pins.
  Transmit and receive LED drive signals.
  UART interface support for 7 or 8 data bits, 1 or 2 stop bits and odd / even / mark / space / no parity

Additional Information:

• Delivery Time: 3 DAYS

Product Details:

The TC7109A is a 12-bit plus sign, CMOS low power Analog-to-Digital Converter (ADC). Only eight passive components and a crystal are required to form a complete dual slope integrating ADC. The improved VOH source current and other TC7109A features make it an attractive per-channel alternative to analog multiplexing for many data acquisition applications. These features include typical input bias current of 1pA, drift of less than 1μV/°C, input noise typically 15μVP-P, and auto-zero. True differential input and reference allow measurement of bridge type transducers, such as load cells, strain gauges and temperature transducers. The TC7109A provides a versatile digital interface. In the Direct mode, Chip Select and HIGH/LOW byte enable control parallel bus interface. In the Handshake mode, the TC7109A will operate with industry standard UARTs in controlling serial data transmission – ideal for remote data logging. Control and monitoring of conversion timing is provided by the RUN/HOLD input and Status output.

Additional Information:

• Delivery Time: 3 DAYS

Product Details:

The IR2153D(S) are an improved version of the popular IR2155 and IR2151 gate driver ICs, and incorporates a high voltage half-bridge gate driver with a front end oscillator similar to the industry standard CMOS 555 timer. The IR2153 provides more functionality and is easier to use than previous ICs. A shutdown feature has been designed into the CT pin, so that both gate driver outputs can be disabled using a low voltage control signal. In addition, the gate driver output pulse widths are the same once the rising undervoltage lockout threshold on VCC has been reached, resulting in a more stable profile of frequency vs time at startup. Noise immunity has been improved significantly, both by lowering the peak di/dt of the gate drivers, and by increasing the undervoltage lockout hysteresis to 1V. Finally, special attention has been payed to maximizing the latch immunity of the device, and providing comprehensive ESD protection on all pins.

Additional Information:

• Delivery Time: 3 DAYS

Product Details:

The AD526 is a single-ended, monolithic software programmable gain amplifier (SPGA) that provides gains of 1, 2, 4, 8 and 16. It is complete, including amplifier, resistor network and TTL-compatible latched inputs, and requires no external components. Low gain error and low nonlinearity make the AD526 ideal for precision instrumentation applications requiring programmable gain. The small signal bandwidth is 350 kHz at a gain of 16. In addition, the AD526 provides excellent dc precision. The FETinput stage results in a low bias current of 50 pA. A guaranteed maximum input offset voltage of 0.5 mV max (C grade) and low gain error (0.01%, G = 1, 2, 4, C grade) are accomplished using Analog Devices’ laser trimming technology.

Additional Information:

• Delivery Time: 3 DAYS

Product Details:

The ADS1212 and ADS1213 are precision, wide dynamic range, delta-sigma Analog-to-Digital (A/D) converters with 24-bit resolution operating from a single +5V supply. The differential inputs are ideal for direct connection to transducers or low-level voltage signals. The delta-sigma architecture is used for wide dynamic range and to ensure 22 bits of no-missing-code performance. An effective resolution of 20 bits is achieved through the use of a very low-noise input amplifier at conversion rates up to 10Hz. Effective resolutions of 16 bits can be maintained up to a sample rate of 1kHz through the use of the unique Turbo Modulator mode of operation. The dynamic range of the converters is further increased by providing a low-noise programmable gain amplifier with a gain range of 1 to 16 in binary steps. The ADS1212 and ADS1213 are designed for high-resolution measurement applications in smart transmitters, industrial process control, weigh scales, chromatography and portable instrumentation. Both converters include a flexible synchronous serial interface that is SPI compatible and also offers a two-wire control mode for low-cost isolation. The ADS1212 is a single channel converter and is offered in both DIP-18 and SO-18 packages. The ADS1213 includes a 4-channel input multiplexer and is available in DIP-24, SO-24, and SSOP-28 packages.

Additional Information:

• Delivery Time: 3 DAYS

Product Details:

The LPC1768 is ARM Cortex-M3 based microcontrollers for embedded applications featuring a high level of integration and low power consumption. The Arm Cortex-M3 is a next generation core that offers system enhancements such as enhanced debug features and a higher level of support block integration.

The LPC1768 operate at CPU frequencies of up to 100 MHz. The LPC1769 operates at CPU frequencies of up to 120 MHz. The Arm Cortex-M3 CPU incorporates a 3-stage pipeline and uses a Harvard architecture with separate local instruction and data buses as well as a third bus for peripherals. The Arm Cortex-M3 CPU also includes an internal prefetch unit that supports speculative branching. 

Features:

• Arm® Cortex-M3 processor, running at frequencies of up to 100 MHz
• Arm Cortex-M3 built-in Nested Vectored Interrupt Controller (NVIC)
• Up to 512 kB on-chip flash programming memory
• Up to 64 kB On-chip SRAM
• In-System Programming (ISP) and In-Application Programming (IAP)
• Eight channel General Purpose DMA controller (GPDMA)
• Ethernet MAC with RMII interface and dedicated DMA controller
• USB 2.0 full-speed device/Host/OTG controller
• Four UARTs with fractional baud rate generation, internal FIFO, and DMA support
• CAN 2.0B controller with two channels
• SPI controller with synchronous, serial, full duplex communication
• Two SSP controllers with FIFO and multi-protocol capabilities
• Three enhanced I2C bus interfaces
• I2S (Inter-IC Sound) interface
• 70 General Purpose I/O (GPIO) pins with configurable pull-up/down resistors
• 12-bit/8-ch Analog/Digital Converter (ADC) with conversion rates up to 200 kHz
• 10-bit Digital/Analog Converter (DAC) with dedicated conversion timer and DMA
• Four general purpose timers/counters
• One motor control PWM with support for three-phase motor control
• Quadrature encoder interface that can monitor one external quadrature encoder
• One standard PWM/timer block with external count input
• Low power RTC with a separate power domain and dedicated oscillator
• WatchDog Timer (WDT)
• Arm Cortex-M3 system tick timer, including an external clock input option
• Repetitive interrupt timer provides programmable and repeating timed interrupts
• Each peripheral has its own clock divider for further power savings
• Standard JTAG test/debug interface for compatibility with existing tools
• Integrated PMU (Power Management Unit)
• Four reduced power modes: Sleep, Deep-sleep, Power-down, and Deep power-down
• Single 3.3 V power supply (2.4 V to 3.6 V)
• Four external interrupt inputs configurable as edge/level sensitive
• Non-maskable Interrupt (NMI) input
• Wake-up Interrupt Controller (WIC)
• Processor wake-up from Power-down mode via any interrupt
• Brownout detect with separate threshold for interrupt and forced reset
• Power-On Reset (POR)
• Crystal oscillator with an operating range of 1 MHz to 25 MHz
• 4 MHz internal RC oscillator trimmed to 1 % accuracy
• Code Read Protection (CRP) with different security levels
• Unique device serial number for identification purposes

Target Applications:

• eMetering
• Lighting
• Industrial networking
• Alarm systems
• White goods
• Motor control

Product Details:

The Microchip Technology Inc. MCP3201 device is a successive approximation 12-bit Analog-to-Digital (A/D) Converter with on-board sample and hold circuitry. The device provides a single pseudo-differential input. Differential Nonlinearity (DNL) is specified at ±1 LSB, and Integral Nonlinearity (INL) is offered in ±1 LSB (MCP3201-B) and ±2 LSB (MCP3201-C) versions. Communication with the device is done using a simple serial interface compatible with the SPI protocol. The device is capable of sample rates of up to 100 ksps at a clock rate of 1.6 MHz. The MCP3201 device operates over a broad voltage range (2.7V5.5V). Low-current design permits operation with typical standby and active currents of only 500 nA and 300 µA, respectively. The device is offered in 8-pin MSOP, PDIP, TSSOP and 150 mil SOIC packages

Additional Information:

• Delivery Time: 3 Days

Product Details:

14-Pin Flash-Based, 8-BitCMOS Microcontrollers withnanoWatt Technology

High-Performance RISC CPU:• Only 35 instructions to learn:- All single-cycle instructions except branches• Operating speed:- DC – 20 MHz oscillator/clock input- DC – 200 ns instruction cycle• Interrupt capability• 8-level deep hardware stack• Direct, Indirect and Relative Addressing modes

• Enhanced Mid-range Core with 49 Instruction, 16 Stack Levels
• Flash Program Memory with self read/write capability
• 128 B of Non-volatile Data Storage
• Internal 16MHz oscillator
• 4x Standalone PWM 
• Complementary Waveform Generator (CWG)
• Numerically Controlled Oscillator (NCO) 
• 2x Configurable Logic Cell (CLC) 
• Integrated Temperature Indicator 
• 8 Channel 10-bit ADC with Voltage Reference
• 5-bit Digital to Analog Converter (DAC)
• MI2C, SPI
• 25mA Source/Sink current I/O
• 2x 8-bit Timers (TMR0/TMR2)
• 1x 16-bit Timer (TMR1)
• Extended Watchdog Timer (WDT)
• Enhanced Power-On/Off-Reset
• Low-Power Brown-Out Reset (LPBOR)
• Programmable Brown-Out Reset (BOR)
• In Circuit Serial Programming (ICSP)
• In-Circuit Debug using a Debug Header
• Wide Operation Voltage Variant ‘F’ (2.3V – 5.5V)
• eXtreme Low Power (XLP) ‘LF’ Variant (1.8V – 3.6V)